|Description: Chip stereo power amplifier, IC: Texas Instruments (National Semiconductor)
Specifications: Cont. avg. output power: 1W+1W (8 ohms). Peak output power: 20W+20W (8 ohms). Frequency range: 40Hz-20kHz(-1dB). Voltage gain: 22dB. Input impedance: 20k ohms.
Dimensions: 240mm(W) x 183mm(H) x 285mm(D) (protruding parts not included). Weight: 4.4kg.
(Amp enclosure: 122mm(W) x 183mm(H) x 135mm(D), Power supply enclosure: 240mm(W) x 82mm(H) x 150mm(D)）
Cost: Approx. 50,000 JPY
History: Conceptional design in 2012. Detailed design in 2014. Built in 2015. Used in Gaudi system as the midrange power amplifier.
Tuning & Measurements
My Own Review
This amplifier, MA-215 Arabesque, is specially designed as the midrange
power amplifier used in Gaudi system (a tri-amplified system). Specifically,
it is the amplifier for the horn-loaded midrange loudspeaker (LS) unit:
Fostex D1405 + H400.
It is my first midrange amp, while I have designed and built a power amplifier for horn tweeters (MA-208).
Gaudi's midrange unit covers 800-6800Hz. Maybe, it should be called the mid-to-treble unit. It covers the band where man's ear is the most sensitive. The midrange amplifier must be particularly low-noise and low-distortion.
I designed a phono equalizer, PE-114 Petit, before I built Arabesque. I postponed building Petit, because I was not satisfied with Flying Mole DAD-M100pro used as the midrange amp. It generated some audible noise and seemed to make the sound a bit unclear. I wanted to solve this problem as soon as possible and gave priority to Arabesque.
What are requirements for the amplifier for the horn midrange LS unit? My answer is as follows (in the order of importance):
1. High damping factor (DF) over mid to treble region
2. Low distortion in treble region
3. Very low noise
4. Moderate output power (not too powerful)
It is a common knowledge that DF affects bass response. Recently, I've
been aware of importance of DF over mid to treble region rather than in
In bass region, DF has an influence on volume. In mid to treble region, it influences sound quality (SQ). With a low DF amplifier, mechanical resonance is not damped and the sound is distorted with airy artifact. Man's ear is so sensitive in treble region that only subtle distortion impairs sound quality.
The High DF (low output impedance) amplifier proves its merits in multi-amplifier system because it is directly connected to the LS unit.
DF decreases as frequency increases in general. There is a possibility that a full-range amplifier's DF is not enough at high frequencies. Amplifiers that are specially designed for mid- or high-range can offer high DF at high frequencies.
This "distortion in treble" is not one caused by mechanical resonance
mentioned above, but one that occurs in the power amplifier. And it's not
harmonic distortion, either. I myself don't have a clear definition about
it. I suppose it is a trigger that interrupts formation of sound image
in human perception process. It might not be continuous but random.
I am unable to define the distortion quantitatively, nor don't know how to measure it, though, I surely feel it. Based on my experience I feel that it is caused by disturbance in signal currents.
I think simple and smooth signal paths would prevent this type of distortion (though it's only a hypothesis). That is, prevention of current reflection, eddy currents and stray currents may be an effective way to prevent the distortion. Specifically, the following methods are effective: reducing excessive cubage and surface area of conductors, shortening signal paths, not bending signal paths at right or acute angle, reducing the numbers of contacts and soldering spots as possible, reducing the number of components, not using large components, avoiding divergence and juncture of signal paths, etc.
As horn speakers have very high efficiency, residual noise must be extremely
low. The target noise level is so quiet that noise can't be heard at deep,
silent night even if the ear is placed very close to the speaker.
The catalog of Flying Mole DAD-M100pro says that its residual noise is as low as 25uV, but noise was heard actually. It is a class-D amplifier and emits RF noise. Probably, the noise is modulated into audible band. I think class-D amplifiers are not compatible with horn speakers.
Output power should be relatively low, since the horn speaker has very
high efficiency. Thorough calculation is necessary to determine the actual
value, because the target value of the output power has big influence on
every step of the design process such as circuit design, part selection
and layout design.
I chose a class-AB solid-state circuit.
The reason why I didn't choose s tubed circuit is that it is difficult to build a high DF amplifier with a tubed circuit.
And I don't think class-D is suitable for horn speakers as mentioned above. I concluded the solid-state linear amplifier is the best.
I decided to use IC (power op amp) for Arabesque.
Experts say that discrete circuits excel ICs, but it's not always true. In actual use, the former needs speaker protection circuits that includes relays and fuses and they may impair sound quality. On the other hand, power op amps include various kinds of protection circuits such as overheat protection and overcurrent protection, and external protection circuits are not necessary. This is a significant advantage.
An low power amplifier can be designed using only one chip. This fact is suitable for Arabesque, whose goal is to reduce distortion in treble region by the small number of parts and short signal paths.
I made the specially designed handcrafted enclosure. It is time-consuming, hard work but worth doing to realize an ideal layout and wiring.
Other than the power op amp, I employed new parts that are of high quality but I hadn't used, such as a troidal transformer and a breaker-switch. In addition, I implemented many ideas that I had been warming over in my mind.
Arabesque is designed and built for use in Gaudi system. For Gaudi II, I will design and build another power amplifier based on Arabesque. In other words, Arabesque is a prototype of the future amplifier.
I named this amplifier "Arabesque." I didn't give this name after
the looks of this amp but its clear sound.
Before naming it, I selected the theme song. I expected clearer sound than DAD-M100pro, so I selected the tune from which I feel clearest ever sound in my collection: "Arabesque No. 1" composed by Claude Debussy, arranged and performed by Isao Tomita (synthesizer) (SACD, Isao Tomita, Clair de Lune - Ultimate Edition, DENON COGQ-59).
I named this amplifier after this theme song.
To the contents
The most characteristic spec of Arabesque is relatively low output power.
I explain it in detail.
It is common understanding that a hi-fi amplifier's output power should be 100W/ch or more. But such big output power is not necessary for horn speakers. The sensitivity of horn speakers is about 20dB higher than today's low sensitivity (
typically 85dB/W or so) speakers. 20dB means 100 times in power. So the output power of the amplifier for horn speakers should be hundredth of the common amplifier. A typical high-end amplifier has 500W/ch output power, so 5W/ch is enough for Arabesque.
Arabesque is used for Fostex D1405 (see the page of SS-309). Its sensitivity is 104dB/W (at 1m). The sound pressure level (SPL) at 5W of the input is 111dB (=10 x log(5/1) + 104). This level could damage man's hearing.
A human feels pain when the SPL is 90dB or more. Even the continuous sound pressure of 90dB may cause a damage if you hear it for a long period of time.
For 20W of the input, the SPL reaches as high as 117dB (=10 x log(20/1) + 104). The combination of the both channel offers 120dB! You must not hear this level of sound even for a short period of time.
Based on this calculation, I determined the target output power of Arabesque: 5W+5W (cont.) and 20W+20W (1 min.).
The output power shouldn't be more than this or less than this.
If it is less than the target, the amplifier might be clipped at peaks. And, to lower the output power, the supply voltage should be lowered, but low supply voltage tends to increase noise and distortion due to characteristic of semiconductor.
You may think excess output power doesn't matter. I don't think so. For the big output power, large components, long signal paths and long current loop are necessary, and those may impair sound quality. Besides, the cost will be increased. I believe
"Too much is as bad as too little."
The well-reasoned, optimized specification is one of the great merits of self-built amplifiers.
To ensure this calculation, I carried out measurement by using my Gaudi system. I chose some music sources with high peak level in my collection. I played them at my usual volume (it's rather big; the peak SPL = 90dB at the listening position) and at unbearably large volume, and measured the peak voltage on the terminals of D1405.
I calculated the peak power levels assuming the voice coil impedance is 8 ohm. The results were only 0.5W and 2.4W, respectively. It was confirmed that the maximum output power of 5W was enough.
I believe low distortion at low output power (less than 1W) is more important than large maximum output power. Especially, low distortion at very low output power (the order of uW) is required for the amplifier for horn speakers.
** As described in "My Own Review," I miscalculated the parameters of the heatsink. I found the continuous output power of 5W+5W cannot be guaranteed. The absolutely safe continuous output turned to be 1W+1W. But it's enough in practical use. I decided to use Arabesque without any modification. I gave Arabesque a nick name "1W Amp."
I thought the gain of Arabesque should be almost the same as the other
power amplifier in Gaudi system (MA-201C and MA-208). They both have the same gain: 18dB. But LM3886 requires the gain of
20 dB or more, otherwise it may become unstable.
I found a design example in the datasheet of LM3886 where the gain is 22dB (approximately 13 times). I decided to copy the component values in the design. I like such a way to evade complex calculation.
I planned not to add an extra feature to Arabesque except the muting switch. LM3886 has the muting function, but I didn't understand how to make use of it. So I added the muting switch to see how it works.
Arabesque has four LEDs as the power indicator. I have used bracket-mounting LEDs before. Though it is easy to mount them on a panel, they don't look cool. I am tired of them.
When I built the preamplifier PA-210 Simplicity, I realized that it looked cool if an LED was mounted behind a transparent screw that fixed the front panel to the enclosure. Transparent screws are also used on Arabesque. I decided to use them as the indicator.
An LED is mounted behind each of the four transparent screws. The two red LEDs indicate VCC (+ supply) for each channel, and the two blue LEDs indicate VEE (- supply).
An ordinary B-curve variable resistors (VR) are used for the input attenuators. The VRs are not necessarily expensive, because they are to be replaced
by fixed resistors in the end.
In the future, Arabesque may be used in my subsystem in the study room. In that case, the VRs are to replace the fixed resistors, since they are needed as the master volume in the subsystem, where no preamp is included.
The frequency range is intentionally narrow.
Especially, bass is not extended. For good bass response, large electrolytic capacitors are needed in power supply. The larger the capacity, the larger the internal inductance. With the large capacitors, the impedance in bass is low, but not so low in midrange and rather high in treble. Large electrolytic capacitors are not used in Arabesque to lower the impedance in treble. Decrease of the gain and/or increase of distortion in bass region are acceptable.
Low noise is the most important feature of Arabesque. I set the challenging target as shown in the table below.
But don't take the value so seriously, because my measurement method is slightly different from the industrial standard like the one specified by ANSI. The value of the residual noise tends to be rather worse with Tonochi-method (because RF noise is included).
I don't regard total harmonic distortion (THD) as the most important thing. In my experience, distortion I feel is different from THD. At present, I don't know any quantitative value that expresses distortion, so I measure THD instead. I don't have a specific target value for THD. If it is not so bad, it's OK (0.1% is good for me).
The table below shows detailed specifications of Arabesque.
|Specifications of MA-215 Arabesque|
|Circuit type||Class-AB Semi-complementary|
|Output power||1W+1W (cont.), 20W+20W (1 min) into 8 ohms|
|Input||1pair single-ended (RCA)|
|Output||1pair multiway binding posts, 1 pair stand-off terminals for soldering|
|Input impedance||20k ohms|
|Load impedance||4-16 ohms|
|Voltage gain||22dB (13x)|
|Frequency range||40-20000Hz （-1dB）|
|Distortion||Less than 0.1% (THD) (not A-weighted)|
|Residual noise||Less than 300uV (not A-weighted)|
|SNR||More than 90dB (not A-weighted)|
|Enclosure||Separate compartments for Amp Board and Power Supply Unit|
The figure below shows the block diagram of Arabesque.
To the contents
The first step to select the power op amp LM3886 was that I spotted it at an online shop I often use for purchase
of electronic components. I downloaded the datasheet from Texas Instruments
(TI) website and scrutinized it. I was convinced it is suitable for Arabesque.
For further information, I googled it and found that it was employed for Jeff Rowland Model 10 (released in 1999). It was a high-end power amplifier priced as expensive as 1.3M JPY, and seemed to be highly evaluated by users.
Some design samples were available at diyAudio (http://www.diyaudio.com/), an online forum I have the membership.
I selected LM3886.
The next most important part is the mains transformer. I decided to use a custom-made transformer for the first time.
At first, I searched for a troidal core transformer online. Though troidal transformers used to be used in audio equipment, it seems that most transformer makers have discontinued them. I couldn't find a suitable one.
I found an R-core transformer for a amplifier kit at the online shop. It is a product of Kitamura Kiden (http://kitamura-kiden.co.jp/). I learned R-core is more advanced than troidal one and suitable for audio transformers. I contacted Kitamura Kiden and was told that Phoenix (http://www.pnxcorp.co.jp/index1.htm) manufactures custom-made R-core transformers and takes orders from individuals too.
According to the Website of Phoenix, the prices are reasonable for custom-made transformers and electrostatic shield is optional.
I selected the Phoenix R-core transformer (see "Circuit Design" for the specifications of the transformer).
For your information, I present "design sheet" I wrote before designing Arabesque. It's an Excel spreadsheet including equations needed for basic circuit design. It may be difficult to understand because it is an only memo for my personal use and not intended to present. Long and short of it is that:
The thermal resistance of the heatsink and the values of the passive components
were calculated by the equations presented in the datasheet of LM3886.
The schematic consists of 2 pages; the page 1 is the schematic of the Amp Board and the page 2 is the main schematic. The reference designator is numbered from 101 in the main schematic (e.g. R101, R102, ...).
The Amp Board is monaural. Two identical Amp Boards are made, and each of them is used for the left and right channels.
The circuit design is based on the design example in the datasheet of LM3886 (the schematic of the example).
I made two changes: one is a DC blocking network (C1, R1) at the front end. The other is mounting the Zobel network directly on the output terminals instead of mounting on the Amp Board.
I still have a question about Zobel network. W. Marshall Leach, Jr. says in his book "Electroacoustics and Audio Amplifier Design", which is my textbook,that the network must be directly soldered on the output terminal and the return line be wired directly to the power supply without being connected to the PCB. On the other side, the datasheet of LM3886 says the network (Rsn, Csn) should be placed as near the chip as possible. Which is right? (I'd appreciate if anyone well-versed in this field would teach me.)
The power supply circuit is included in the main schematic.
The mains transformer has two secondary windings. Each of them is used for the left and right channels. This makes it possible that each channel has separate ground wiring. It increases flexibility in wiring design, though it is not so helpful to improve channel separation because the two windings are coupled electromagnetically in the transformer.
|Specifications of mains transformer|
|Secondary winding||AC20-0-20V 1A x2|
|Protection||250V 2A 115degC thermal fuse|
|Dimension||120.5(W) x 49.9(H) x 88.9(D)mm|
The rectifier circuit is an ordinary full-wave rectifier.
The diodes are schottky barrier diodes (SBD), whose forte is low switching noise. The reservoir capacitors are 4700uF electrolytic capacitors (E-cap). It is rather small value but enough to obtain 15% of regulation in the 20W amplifier. I believe 15% of regulation is enough for LM3886, whose PSRR is pretty high (=105dB).
I didn't spend much time and effort to select the e-caps for the reservoir capacitor. I chose 35V/4700uF in Nichicon KW Series. It is audio-oriented but not the highest grade. It is designed mainly for A/V devices. And the working voltage doesn't have a wide margin. I chose it because I give the top priority to high density assembly with small components.
I didn't make matched pairs of E-caps for the reservoir capacitors.
Technically, the absolute values of VCC(V+) and VEE(V-) must be the same. So the capacitance values of the reservoir capacitors must be the same for both VCC and VEE. The capacitance tolerance of E-caps is so large (+/-20% for KW series) that it's necessary to find matched pairs among many e-caps by measuring capacitance actually.
I didn't do that, because LM3866's PSRR is high enough and its output stage is semi-complimentary (the loads of VCC and VEE are not the same).
As in other NOBODY amplifiers, the AC line noise filter is inserted between the AC line and the mains transformer. The Tokin MR-2454 decreases noises in 500kHz-10MHz band, which are the most harmful for audio amplifiers, by 40 to 70 dB.
I use the breaker switch as the power switch for the first time. It is the combination of a circuit breaker and a switch. By using this, a fuse can be omitted and the wiring can be simplified. It is a product of Nikko Electric and the model name is IBP-1-2A. The break current is 2A and the break speed is medium.
I wondered if I should order PCBs to a PCB maker for the first time, but
I didn't, because the number of components was small and Arabesque does
not treat very small signals.
I made the circuit boards from 2mm thick bakelite boards. These boards have the mounting holes unlike the circuit boards of CD-211 A-NET and HA-213, which were hole-less 3mm thick bakelite boards. With the holes, components can be mounted just as PCBs. The circuit is formed by soldering components' leads each other directly. I call this type of circuit board "P2P (point-to-point) board."
The diameter of the mounting hole is 1.5mm (the standard diameter is 0.8mm for PCBs), so that the components' leads can go through the holes slantwise.
The leads shouldn't be bent at right or acute angles. Otherwise, current reflection will occur at the bending points and this may cause distortion. With the PCB, the leads cross the printed wiring at rights and current reflection is inevitable. With the P2P board, the leads can be bent in a loose arc and current reflection is prevented.
One more strong point of the P2P board is reduction of solder joints in number. Two components are jointed by one soldering on the P2P board, while at least two solderings are needed on the PCB. To make better contacts, the leads are twisted together and contacted each other before soldering.
I used a PCB CAD, though I didn't order PCBs to a PCB maker. It was my first experience. I never designed any PCB using a CAD even when I was an engineer.
The PCB CAD (CADLUS X, see "Misc Info" for the details) is not easy to use, because its manual is not easy to understand and it doesn't have help feature (only the manual is displayed by clicking the Help menu). I struggled to understand how to use it.
Two kinds of boards are made: "Amp Board" and "Rectifier Board." The circuit of Amp Board corresponds to the first page of the schematic. The circuit of Rectifier Board is included in the second page of the schematic.
I didn't use the CAD to design Rectifier Board, because it is so simple. It has only several mounting holes for the diodes. The reservoir capacitors are not mounted on the board but soldered on the diode's leads directly.
I designed Amp Board as a double-sided, through-hole PCB using the CAD. In practice, all the wiring is done on the printed side.
The heatsink for LM3886 is secured on the Amp Board with screws. The easiest way is mounting the chip on the chassis (the chassis works as the heatsink). But it is not good because vibration of the chassis is directly conducted to the chip. It is better to mount the heatsink on the chassis with vibration-proof material between them, and to expose the fins of the heatsink outside. I didn't choose this way, because Arabesque doesn't generate much heat.
The heatsink is connected to SG (signal ground).
All the ground traces are gathered at the ground hole located near the chip. The ground hole is wired to the chassis ground (the connecting point of SG and FG). The return line of the bypass capacitors (C8, C9), called noise ground or NG, is connected to the chassis ground with another wire.
[PCB design of Amp Board]
(In the drawing, the name of the board is Main Board, because I called it so when I was designing it)
The enclosure is designed to serve the purpose perfectly, taking advantage of the home-made enclosure.
This enclosure consists of the dirty and clean compartments as in a preamplifier. It is a compact one unlike commercial large and heavy amplifiers, and the power supply circuit is located near the amplifying circuit. To prevent noise from the power supply, it is accommodated in the dirty compartment, where AC currents other than the signals are acceptable. The amplifying circuit is accommodated in the clean compartment, where no AC currents other than the signals are acceptable.
The both compartments are combined with screws to form one enclosure.
All the ground wirings are concentrated at one point called "chassis ground." It is located in the clean compartment and close to the boundary between the clean and dirty compartments. The grounds of the both channels are connected here.
The chassis ground is wired to the center taps of the secondary windings of the mains transformer with shortest possible wires (the length is less than 10cm).
The Amp Boards are fixed to the studs in the enclosure with screws. So they are detachable unlike the boards of CD-211 A-NET and HA-213, which are secured with adhesive tape. For vibration insulation, two rubber washers are inserted between the board and the stud.
It is unusual for NOBODY amplifiers, but the multiway binding posts for loudspeakers (Amtrans CP-212) are used for the output terminals. However, these posts are used only for testing and evaluation, and will be used as the holder of the cable sheath. The stripped wire will be soldered to the stand-off terminal beside the binding post.
The cheap RCA jacks (with small cubage and surface area of metal part) are used for the input as usual.
The location of the VRs for the input attenuator is determined, giving good appearance the top priority. At the end, the VRs will be replaced by fixed resistors, so the lengths of the wires are not important.
It is another first experience of mine that all the wirings are done with OFC wires (I used to think electrolytic-tough pitch (ETP) copper is good enough for audio amplifiers).
And, I chose gold-plated OFC wire (Amtrans GW-T-0.7Of) instead of tinned copper bus bar. You shouldn't use the tinned copper wire if you stick to high purity of copper. It used to be impossible to plate gold directly onto copper (nickel-plating was needed before gold-plating). Amtrans' breakthrough has made it possible. GW-T-0.7Of has a thin jacket. By stripping it, the wire can be a substitute of the tinned copper bus bar.
The unique appearance of the enclosure, vertical style of the front portion
and horizontal style of the rear portion, is one of the main characters
of Arabesque. This unique style is not aimed at drawing attention but at
fulfilling the technical requirements.
The requirements are: 1) compact and well-suited shape to install on the bottom shelf of the TV rack; 2) shortest possible current paths (the paths that carry large currents, e.g. the supply lines, ground lines, etc); 3) smooth air flow inside the enclosure that helps heat release with the small number of vent holes; 4) effective shielding.
The reason why the front portion (clean compartment) is vertical is that the Amp Board should be vertically mounted so that air can flow upward along the board and pass through the gaps between the fins of the heatsink. This enclosure is nearly air-tight aiming at good shielding effect. That good air flow ensures enough heat release.
Another solution to improve heat release is matt black paint on the inside walls. I haven't seen such amp enclosures so far, but I think it is recommendable for DIY constructors since it is rather effective.
To achieve high channel separation at high frequencies, the clean compartment consists of two separate compartments for the left and right channels. I chose the easiest way to build it: combining two simple chassis.
I employed the simple finished chassis with a bottom plate, Lead P401 (1t 180x130x60mm), for the clean compartment. Two unit of P401 are combined on each other. Though it is already finished, the paint is removed except the side surfaces (that turns to be the top and bottom surfaces) and the bottom plate (that turns to be the side panel).
The front surface of the clean compartment is painted mat black. The inside walls are also painted mat black.
The side panel is a 1mm thick aluminum panel and very likely to vibrate. I decided to attach a copper panel (1x100x100mm) onto it. The combination of the different materials dampens vibrations and resonates. The two panels are fixed with as many as 13 screws to be united perfectly. Silicon grease is applied between the two panels for lower thermal resistance.
The metallic silver face panels are attached to the front and back of the clean compartment. They are secured with transparent plastic screws.
It's another first experience of mine that transfer paper (A-one 51112) printed with PC is used instead of instant letterings.
The dirty compartment is a 100% DIY case. Every part is made of aluminum panels, channels, angle or square bar. The parts are fixed with screws each other to construct the case. This way, you can build a case in optimal dimension.
The dirty compartment is horizontal style, because it is suitable to accommodate the mains transformer.
At first, I planned to place the rectifier circuits in the dirty compartment, but placed them in the clean compartment, because I found an enough space for the circuit in the clean compartment. This makes the lengths of the wirings shorter and the same between the both channels, because Arabesque has separate rectifier circuits for the L/R channels.
Two aluminum channels are inserted between the mains transformer and the chassis to reduce propagation of vibrations from the former to the latter. The channels are stuffed with soft putty to deaden vibrations.
I wondered if the frame of the transformer should be electrically floated. I contacted the maker of the transformer (Phoenix) and learned it should be grounded. I decided to use handmade copper washers between the frame and the channels. They are made of a 0.1mm thick copper sheet folded 6-layered. The washer is at once a good electrical conductor and deadener.
The following is the drawing of the enclosure.
[Drawing of Enclosure]
Recently, I am more interested in mechanical design than in circuit design. I was carried away when I was designing the enclosure and it turned to be rather unique. The number of the screws has exceeded 200. However, I dared to build it as designed, because I thought the screws would be helpful for dampening vibrations and improving electrical and thermal conductivity (though an enclosure made of one metal plate is better in conductivity). All the screws but plastic and aluminum ones are used with inner clip washers to improve conductivity.
Five types of screws (steel, stainless steel, brass, plastic, aluminum) are used. The steel is used in the dirty compartment. In the clean compartment, nonmagnetic screws are used: stainless for the enclosure assembly, brass for the side panels, transparent plastic for the front face panel, and aluminum for the boards and the heatsinks.
A finished aluminum plate if used for the face panels. After lettering, they are painted mat clear. Mat clear looks good even if it is painted a little uneven, compared to gloss clear.
I compiled the procedures of metalwork in a manual so that I could concentrate on the work without thinking of things complex when I actually worked. It really improved productivity.
[Manual of metalwork]
The following is the BOM of Arabesque.
BOM is as important as drawings such as the schematic. However, I hasn't presented any BOM before, because I didn't maintain BOMs in a proper way and they were not reliable.
From now on, I will maintain BOMs and disclose them.
Well-maintained BOMs lead to accumulation of know-hows. For example, you can't identify most parts in a schematic, since model numbers and manufacturer names are not written except for key parts like ICs and transformers. Replacement of only one part may change sound quality. The information about each part should be documented. That is, you should create a BOM. It is rather risky to rely on your memories. You should update the BOM whenever you replace (a) part(s) with different one.
If the BOM includes the prices of the parts and vendor names, it will be a good reference at next design.
To the contents
I processed each part according to the manual. I rearranged the whole procedure according to the actual conditions.
I began with small parts I could process indoors.
|Aluminum channels for the
dirty compartment （CH1-CH4）
|Aluminum channels for the
mains transformer module （CH5-CH6）
|Processed small parts|
The heatsink (Fischer Electronik SK 487/37.5 SA) is a clip type (the IC
is secured with a clip). I bought the clips (Fischer Electronik TGFU 1)
too when I bought the heatsinks. But I found out that the IC (LM3886) couldn't
be firmly secured. No choice but I made a hole in the heatsink and made
a thread for M3 screw. The right photo shows tapping the hole.
It was April when I finished metalwork of the small parts. It is the best season for outdoor DIY. I set up my work bench in my yard and started full-scale metalwork.
I tried two methods of cutting metal plates: using an acrylic cutter, and using a power zigsaw.
Precisely straight-line cutting without burr is the strong point of the former method. I have used this method for all the previous works.
|(1) Make a groove
along the mark-off line
|(2) Insert the plate between two
wood boards and bend it
up/down along the groove
till it's cut apart
|(3) Cut surface
No burr is seen
A power drill has been an only power tool for me. This time I added a power
zigsaw and a power sander. They were both bargains at a nearby DIY store.
I tried the power zigsaw to cut the perforated aluminum plate whose cut surface would not be seen from outside. I made a straight-line guide beforehand. I was happy with the result. It was so easy and no burr was seen. Less than one tenth of effort is needed than the former method. The 3,680-yen-priced tool made a big difference. I regretted I should have bought it earlier.
One more advantage of the power tool is that up to 5mm thick aluminum plate can be cut with it, while 1.5mm is the limit in the former method. Also, thin steel or copper plate can be cut with the power zigsaw. I determined to use it always to cut metal plates from then on.
It was so useful to cut the aluminum square bar and angle. If I had used a hand tool, not only I would have consumed time but also big errors would have occurred.
All the cuttings were done.
|Angles (A1-A10) (upper)
Square bars (B1-B4)
Making the copper washers
|Top and bottom panels
|Copper sheets for ICs (left)
Copper washers for transformer
The next step is processing the simple chassis (C1, C2) for the clean compartment.
First, I made mounting holes needed to combine C1 and C2.
Secondly, I removed the paint off the main wall of the chassis to reduce electrical resistance between C1 and C2. I used my new power sander, but the paint was hardly removed. Maybe, it's better to use a paint remove agent.
Thirdly, I removed tabs that are obstacles to attach the square bars with a hand nibbler. The square bars are at once reinforcement and female screws to secure the side panels (P3, P4).
|Simple chassis with mounting holes
|Removing paint||Removing tabs|
I confirmed the positions of the mounting holes of the chassis and broadened
the holes with a small round file if misalignment was found.
I actually attached the square bars (B1-B4), then detached them after confirming they were in place.
After amending misalignment, C1 and C2 were screwed each other. The combination was handled as one part thereafter.
Inner clip washers made of stainless steel were inserted on both ends of the screws. These screws would be unable to tighten in the following steps, so screw lock agent (ThreeBond 1401B) was applied to each screw in order to prevent loosening semi-permanently.
Also in the following steps, screws that are not supposed to remove were locked with the agent.
|Trial attachment of square bar
|Combined C1 & C2||Locked screws||Screw lock (ThreeBond 140１B)|
It was time to process the face panels since I already got used to metalwork.
First, I cut out the panels (P1, P2, P5).
Next, I made mounting holes that were necessary to screw the panels together with the clean compartment (C1, C2). Other mounting holes were not made yet.
I stopped metalwork here, and assembled the enclosure temporarily to confirm its construction.
I assembled it correcting position errors of the mounting holes by widening the holes with the small round file. It took me more time than I had estimated. If I had made larger holes in the first place, the labor hours would have been shorter. But I drilled just 3mm holes because the inner clip washers were used with all the screws.
The first step of the assembly was making the side channels out of the channels CH1-CH4. Then they were screwed with the bottom panel (P8).
Next, the clean compartment (C1, C2) was screwed with P8.
Lastly, the temporal assembly was finished by attaching the other panels (P1-P7).
|Side channels of dirty compartment||Assembling the dirty
|The 1st temporal assembly
|The 1st temporal assembly
I removed the dirty compartment, and drilled the rest of the mounting holes
in the face panels (P1, P2, P5) and the clean compartment at the same time.
This way prevents position error of the holes between the compartment and
I cut out blowholes in the top wall of the clean compartment, its side panels (P3-P4), the bottom panel (P7) and the top panel (P8) with the power zigsaw.
I made through-holes in the side panels P3 and P4 with the reinforcement panels P9 and P10 attached on them, respectively.
|Drilling the face panels
|Blowholes in the clean compartment||The side panels of the clean
compartment (P3, P4)
At last, metalwork was completed by amending the holes with files..
I did temporal assembly once more in order to make sure there was no mistakes in design and metalwork. This time, all the parts were mounted temporarily.
I made the mains transformer module (MT module) in advance by attaching the channels CH5, CH6 to the mains transformer. The copper washers and outer clip washers were inserted between the frame of the transformer and the channels in order to deaden vibrations and ensure electrical conductivity. This module was not to be disassembled, so screws were locked with the screw lock agent.
Just like the first temporal assembly, it began with assembly of the dirty compartment.
|MT module||Under assembling||2nd temporal assembly completed|
I found some faults.
The position of the power switch is too high, and the distance between its lead and the top panel (P7) was only 10mm or shorter. It doesn't conform with NOBODY standard. The clearance between a high voltage part and other conductive material must be 15mm or more in both airline and creepage distance. I affixed an insulation sheet (PET sheet) on the inner surface of the top panel.
The position of the output terminals is not good either. The clearance between them and the top panel (P7) is not enough. And the hot (red) and cold (black) terminals are so close that they could be short-circuited unless you are careful enough. In addition, the terminals block a screwdriver when you tighten the screws
It is hard to solve these problems, I've decided not to anything about them. In the near future, the output terminals will turn to be only holders for the speaker cables. I plan to change the hot terminals to ground terminals. And I omitted the screws below the terminals.
|The position of the power switch||The position of the output terminals|
Now that I took trouble to assemble the enclosure, I disassembled it and
washed all the mechanical parts in soap and water.
I was surprised when I removed the protect film off the face panels (P1, P2). The material (Lead NP22) was not painted in silver, contrary to my expectation. It was only hair-line finished.
No choice but I decided to paint them before lettering.
I used water-based spray paint recommended by the nearby DIY store. The store clerk said it could be used on an aluminum panel if you use a primer for nonferrous metal.
But I used acrylic paint for automobile for silver color because no good-looking water-based silver paint was available. And I used mat clear spray paint I had bought before.
The right picture shows the spray paints I used: (from left) primer (water-based, for nonferrous metal), silver gray (acrylic), mat clear (acrylic) and mat black (water-based).
I made a windbreak box with a door from cardboard. I placed mechanical parts in it and sprayed. As soon as I sprayed, I shut the door. Thanks to this box, the sprayed paint didn't diffuse and waste of time and energy was reduced.
Most parts were painted twice. Only silver gray was painted three times.
After three days of drying the painted parts, I did lettering on the face panels (P1-P2, P5-P6).
I transferred letters printed on the transfer paper with PC on the silver gray face panels (P1-P2). I should have tried it beforehand, since it was my first experience, but I skipped the training because the paper was so expensive.
I was not happy with the result. I printed the letters using pigmented ink, though it was not fit with the paper. The letters turned to be blurred. The font size was so small that the blur looked worse. Besides, a part of the ink was dissolved by water that was needed to remove the backing layer. I realized too that it was difficult to transfer a string of letters horizontally when the font size was so small.
It's embarrassing to disclose my failure, but I dare show the photos of the face panels for your information.
As for the black face panels (P5, P6), I affixed instant letterings on them as I used to do. I did this task without any problem.
After lettering, mat clear paint was sprayed on the panels.
The photos below show the front face panel (P1) and the rear face panel (P6).
The circuit boards were made from a 2 mm thick bakelite board.
I came up with a good idea. I transferred the drawings of the board I had drawn with a PCB CAD on the boards. You can see at a glance the positions of the parts and holes, and the wiring. It was so helpful for all the processes: drilling, mounting, wiring and even maintenance.
The drawing includes copper patterns of the both sides and silk screen print. You can see the copper pattern of the printed side from the component side. The mirror image was transferred on the printed side so that you can see the copper pattern of the component side.
It was a really good idea, even if I do say so myself. But my printer got out of order while I was printing the drawings, so I couldn't do it for all the sides.
The diameter of the mounting holes was as large as 1.5 mm, so an ordinary power drill could be used. I attached my power drill to the drill stand and drilled the holes. The number of the holes was not large. It took me less than one hour.
I realized that adhesive force of the transfer paper was so strong that it could never be removed once it was transferred. In case it is transferred on a face panel, clear paint is not necessary to fix the letters.
As soon as I finished drilling, I assembled the boards. I did it without any trouble thanks to the transferred copper pattern and silk screen print.
I bent the leads of the components into an arc as loosely as possible to prevent current reflection. Of course, I soldered them in my Tonochi Method (I'm going to explain it in another page). I used the thickest soldering tip for all the soldering spots.
When the lead of the component was too short, I used the gold-plated wire (Amtrans GW-T-0.7Of). It is easy to use because it is a single wire.
The IC (LM3886) was screwed to the heatsink with an aluminum screw and a plastic washer. The handmade copper sheet (0.1mm thick) was put between the IC and the heatsink. The silicon grease was applied to reduce thermal resistance. The grease may appear thick in the photo below, but I applied it as thin as I could.
The rectifier diodes and a noise absorption capacitors were mounted on the Rectifier Board. The reservoir capacitors were mounted after the board was mounted in the enclosure.
|The ICs screwed down to
|Assembled Rectifier Boards|
The enclosure was going to be built for the last time.
Stainless steel inner clip washers were used with the all the metal screws except the aluminum ones.
First, the perforated panels for the air vents (PP1-PP6) and the copper reinforcement panels (P9-P10) were fixed.
Then, the mains transformer module (MT module) was fixed on the bottom panel (P8). The channels were filled with soft putty to deaden vibrations.
|Side panels (P3-P4) with perforated
and copper panels screwed on them
|The fixed MT module|
After attaching the front panel of the dirty compartment to the clean compartment,
I screwed them on the bottom panel (P8). Before assembling the rest of
the enclosure, I wired the MT module and other high voltage components.
I had planned to use Belden 19364 for the power cable. But its sheath was so stiff that it couldn't be bent acutely. It is good for sound quality, but not easy to use during checks and measurements. I decided to use my old power cord with an AC plug (1.25mm2) tentatively. I was going to replace it with Belden later and check the difference in sound quality between them.
I mounted the Rectifier Boards and the bleeder resistors in the clean compartment, and wired them. The power supply circuit was completed by mounting the reservoir capacitors (35V/4700uF) on the Rectifier Boards.
The LEDs for the power indicator were mounted on tag strips (1L2P) to modularize them. They were fixed on the inside wall of the enclosure with the transparent plastic screws that also secured the front face panel.
The Amp Boards were mounted, but not wired yet.
|Wiring of the high voltage circuit||Mounting & wiring of the rectifier
|Installation of the LED module|
Now I was going to turn on Arabesque for the first time to check the power supply circuit (we Japanese call it "hiire-shiki" that means first-power-on ceremony). This wouldn't damage the power supply because the bleeder resistors and the LEDs worked as a load.
I experienced so many hiire-shiki, though, I was thrilled again.
Before the first power on, I checked the circuit with my DMM, and measured voltages in the power-on state (see "Tuning & Measurements" for the details).
I didn't notice any trouble. The power supply circuit worked. The only problem was that the power indicators shone too brightly because the LEDs were ultra-bright type. I halved the current to 4mA, and tilted the LEDs to reduce amount of light emitted outward.
I did the rest of the wiring.
I had planned to solder the Zobel network (Rsn, Csn) on the output terminals, but it was hard to do that because there wasn't enough space in the clean compartment. I probably could manage that somehow, but I gave it up due to my misunderstanding that the compression driver D1405 didn't need the Zobel network so much.
|Wiring in the clean compartment (L-ch)||Wiring in the clean compartment (R-ch)|
The last step was attaching insulators and the knobs.
I used urethane foam as the insulator. I had originally planned to use Hanenite Rubber and felt, but changed my mind because the urethane foam was cheaper and easier to use. I affixed it with butyl rubber adhesive tape (Fostex BN50).
To the contents
It was the end of July when I completed the assembly. It was the best season
for checks and measurements.
The higher the ambient temperature, the severer the condition for the amplifier. If the amplifier works in summer, this indicates it works in the other seasons too. And the day is longer in summer, so the room is light all day by the sun. Electric lights should be off to prevent electrical noises. I even turn off all electrical appliances but the refrigerator and the ventilator during measurement.
I documented the conditions and procedures of the measurements for the first time. I have made Excel spreadsheets for data input before measurement. Though the spreadsheets were useful, I sometimes got confused by forgetting the conditions afterward. It was troublesome to redo the measurement. This time, I planned well and made the documents to avoid waste of time and labor.
Going back to mid July, when I turned Arabesque on for the first time.
I carried out wiring check before the first power on, and voltage check
during the power on.
I didn't find any fault in the resistance check. I was only concerned about the inner resistance of the breaker-switch, which I used for the first time. My measurement was 0.4 ohms, while the value specified in its catalog was 0.25 ohms. It should include much error because the value was nearly the limit of my instrument (DMM: SANWA PC710). Anyway, it was rather high resistance for the AC line. [Result of resistance check]
In the voltage check, I measured voltage with Amp Boards not connected to the power supply at first. After I confirmed the power supply circuit was OK, I connected the Amp Boards. The absolute values of the DC power supply (VCC_L, VCC_R, VEE_L, VEE_R) was slightly less than 30V, and they rose up in 0.3 seconds at power on. [Result of voltage check]
I noticed that the surface temperature of the ICs rose more than I had anticipated. It reached 55 deg C after 10 minute running. I had assumed that the temperature wouldn't rise in idling state, though I hadn't calculated. I read back the datasheet and found it says the total quiescent power supply current is 50mA. It is natural the temperature rose, because the power dissipation is 3W (=60Vx0.05A) when the DC power supply is 60V(+/-30V).
This measurement was aimed at confirming Arabesque worked as a hi-fi amplifier.
The measured data meant Arabesque didn't have any big fault rather than
proving its high sound quality.
The following data were measured:
Left: 425uV, Right: 444uV
I was disappointed at this result. But it was not the final measurement. The data was measured with the lids (the side panels P3, P4 and the top panel P7) removed, so some environmental noise might have been mixed. By the way, A-weighted filter was not used.
Left: 22.39dB, Right: 22.38dB (output=1kHz, 1W)
It was exactly what I had expected. The channel balance was perfect. It is one of advantages of chip amps.
The level of crosstalk was far less than that of the residual noise, and it was unable to indicate crosstalk in numbers.
The response in the low band was exactly what I had expected. The response
in the high band was not. The upper cutoff frequency was lower than I had
expected. The value of the lag compensation capacitor (C11 = 22pF) was
a little too large.
The frequency range of Arabesque can be expressed as 40Hz-25000Hz (-1dB).
The figure below shows a peak at 250kHz. I saw it and realized that it is rather difficult to make full use of power op amps. Unlike discrete circuits, the response of the power op amp tends to extend to 200-300kHz even in open loop condition. So it is likely to oscillate in high frequencies. I'll discuss the problem later in "My Own Review".
I measured response at very low frequencies (1Hz-10Hz) later, and found no peak. The gain naturally falls as the frequency lowers.
The waveforms at 100Hz and 1kHz were perfect. But ringing appeared at 10kHz.
I spotted the ringing for not only output waveform but also input. I had never experienced such a phenomenon with tube amplifiers. I suppose it is "feed through distortion." That is, the distortion of the output goes to the input via the feedback loop and distorts the input signal.
I added a 0.47uF capacitor parallel with the dummy load (8 ohm resistor)
to check stability.
The ringing of the left channel was a bit larger than the right channel. But it didn't escalate to oscillation and disappeared within one forth of the wave length. I judged it was OK with a narrow margin.
During the measurement, the input low-pass filter was removed, though it was used in practical use. I think you can ignore the risk of oscillation in practical use.
It is rather difficult to observe true waveform with an oscilloscope. Again, I had to repeat the measurement as changing the conditions in trial-and-error manner.
For the further details, see the following memo. [The measurement of square wave response]
There seem to be some variations in measurement method of output power. I measured it in the following conditions:
The environmental condition was as follows:
The results were:
Left: 24.2W, Right: 26.0W
I felt a sudden dear that the IC (LM3886) might have overheated. The package temperature exceeded 100 deg C (reached 101 deg C). The IC has an overheat protection feature, though, it only activates at a very high temperature. I am convinced that its purpose is prevention of serious incidents like a fire. You should be careful when you measure the maximum output power, because the IC might be stressed and sound quality could be impaired.
I measured the maximum instantaneous output power too.
Left: 26.8W, right: 28.1W
I designed the power supply circuit a bit roughly, though, the regulation turned to be 12-13% at 20W of output. It was better than the target of 15%. If the maximum
power is supposed to be 1W, the regulation is approximately 4%.
The following waveforms show ripple of the DC power supply observed at output of 0W, 1W and 20W. There isn't significant difference between the left and right channels, so the figures show the data of the left channel only.
After finalizing Arabesque, I conducted the final measurement.
So far, I found some minor problems. After all, I decided not to solve any of them.
The differences from the previous measurements were: 1) the lids (side panels P3-P4 and top panel P7) were attached, and 2) the power plug was connected directly to a wall outlet instead of using a power strip.
I made the following measurements:
The input was 1kHz sine wave. The output was set to 0.01W, 0.1W, and 10W
in addition to the standard 1W. The "Half" in the table below
means the input attenuator was set to the middle position. Since a B-curve
VR was used for the attenuator, the input level was halved (-6dB). The
output power was 0.25W, which was one fourth (-6dB) of 1W. This measurement
was meant to clarify how the attenuation affects distortion and/or noise
The right channel kept low THD for all the output levels, but THD of the left channel tended to increase as the output power increased. But I didn't care the result, because the accuracy of this measurement was not so good and the data were better than the target of 0.01%.
For SNR, the measurement was less accurate. So the values are not so reliable.
The figure below is the data for the left channel at 1W of output.
The data were almost the same as the previous measurement. It may be natural
because any change was not made including the lag compensation capacitors.
I measured data when the output was 0.1W and 0.01W, and the input attenuator was set to the middle (-6dB). The result was the same as the previous one.
Left: 407uV, Right: 430uV
To my disappointment, these values are almost the same as the previous data. I had expected so small values because the datasheet of LM3886 says its noise floor is 2.0uV. But Arabesque didn't live up to my expectation.
By the way, the residual noise of MA-208 was 176uV in the same measurement condition. That of DAD-M100pro was 171mV when it was connected to D1405. DAD-M100pro was far noisier.
This time, crosstalk was measured at the output power of 10W. If the output is 1W, crosstalk may be buried in residual noise.
The table below shows the result. I found one thing I couldn't understand. Crosstalk was detected in high frequencies when the direction was R to L. But no crosstalk was detected when the direction was L to R. I redid the measurement later, but I got the same result. I can't explain this phenomenon (if anyone who is well-versed in this field would help me, I'd appreciate it).
Linearity was perfect. The table below shows the data of the left channel.
The same data were measured for the right channel.
The high DF was the most important target for Arabesque. I was satisfied
with the result.
Though the data below may have some error, the values are as high as 650 or more at 1kHz and 130 or more at 10kHz. It is 70 or more even at 20kHz. If Arabesque were a tweeter amplifier, 100 at 20kHz would be desirable, but 70 is enough for the midrange amp.
I spent about one month for the measurements. At last, I began listening test I couldn't wait for.
First, to be on the safe side, I used my old LS unit (Fostex FE106 Sigma), which I didn't care if it was damaged, though I was confident with stability of Arabesque since it didn't cause any problem during measurement conducted in 30 deg C environment. I made sure oscillation and unnatural noise didn't occur.
Then, I used Arabesque as a full-range amplifier with my speaker system SS-312. Without a preamplifier and a network, the power amp's sound quality and tonal character are revealed well.
And, I used my old midrange module SS-309M (the LS unit is Fostex 6N-FE88ES) that had been used in SS-309 before, because SS-312 was not in good condition after a long unused period. I compared Arabesque with DAD-M100pro and MA-208, too.
I short-circuited the input of Arabesque, connected Fostex FE106 Sigma
(that was not installed in an enclosure) and my oscilloscope to the output,
and turned on. No oscillation occurred, and no noise was heard. I didn't
sense the transition of power on/off, either. So far, so good.
I sensed a minute hum noise when I put my ear very close to the left channel speaker. I didn't noticed it when I measured residual noise because it was buried in random (white) noise.
I figured out the cause soon. Leakage magnetic flux came out from the breaker switch (Nikko Electric IBP-1-2A), which I used for the first time. The distance between the switch and the IC (LM3886) was so short (about 10cm) that hum noise of 50Hz was induced. I hadn't thought of this problem at all. The switch is not shielded, so its leakage flux is stronger than that of the mains transformer. The switch mustn't be situated near the IC. I don't think it is suitable for a compact amplifier like Arabesque.
I didn't do anything about it because the noise was so small.
I played CD quality WAV files with Arabesque and my subsystem in the study
room (loudspeaker: SS-312, player (digital recorder): TASCAM DR1).
I was disappointed at once. It sounded cheaply like a boom box. Compared with MA-205A, it offered more natural and likable sound.
This low sound quality (SQ) was partly due to bass-deficient sound of SS-312. Besides, the DR1's SQ is not so good for a player (its recording SQ is good). I decided to use Gaudi's components instead of the subsystem.
During the listening test, I measured temperature inside Arabesque with my DMM and temperature sensor (thermo couple). The temperature immediately above the heatsink was 52 deg C at the maximum when the ambient temp was 29 deg C. It was no problem at all. I confirmed Arabesque could be used as a full-range amplifier.
I wanted to know performance with the real load (loudspeaker), I did FFT analysis with SS-312 connected to Arabesque. As the table bellow shows, the result was all most the same as the previous one with the dummy load.
For comparison, I measured MA-205A too. As I had expected, Arabesque's performance was better.
I used the components in Gaudi system: SACD player SONY SCD-555ES, analog
disc player, PS-104, preamplifier PA-210 Simplicity, MC head amp HA-213. SS-309M was placed on the woofer box of SS-309 just as it used to be. The AC power source for Arabesque was the wall outlet for audio.
Arabesque sounded better this time. I wondered if its SQ might be affected by the quality of the AC power supply.
I compared Arabesque with DAD-M100pro and MA-208 too. I felt Arabesque was the best. I ranked them as follows:
Arabesque > MA-208 > DAD-M100pro
The sound of Arabesque was clear and spacious with well-defined and stable stereo imaging. Particularly, vocals and violins sounded vividly.
I played LPs, SACDs and CDs I always use in listening tests (see "Tuning"). In addition to these, I used the following CDs:
Various artists, For Jazz Audio Fans Only Vol.1 (CD, Terashima Records TYR-1004)
Various artists, Best Audiophile Voices (CD, Premium Records, XRCDPR 27901)
Experts say the input attenuator of the power amplifier should be set at maximum (=0dB). I did so during the listening test.
For a trial, I set the attenuator to the middle (-6dB). Theoretically, SNR gets to the worst in this condition. I turned up the volume control of the preamp so that the volume remained the same.
I didn't sense any difference in SQ. I repeated the test a few times, but still I didn't tell any difference. Maybe, only very sensitive person can tell (I'm not so sensitive). There was no significant difference even in the measured data. I don't think I should stick to this matter.
It is risky to jump to conclusion after one listening test or two. SQ varies according to various factors. Even mood or physical shape of the listener could affect. I repeated the listening test with my favorite discs (chiefly LPs) under different conditions.
I was gradually getting discontent. The sound of piano was unnatural though the sounds of percussion and brass were so good. I couldn't figure out the cause.
The SACD player (SCD-555ES) was directly connected to Arabesque. The preamplifier
wasn't used. I played SACDs and CDs.
Still, the piano sounded a bit funny. Sibilance of singers' voices was a bit intense. Totally, Arabesque sounded cheaply.
I used the preamplifier PA-210 again. I compared Arabesque with DAD-M100pro
and MA-208. I played only one CD (Herbie Hancock, Gershwin's World, Verve UCCV-9366) and concentrated on a few tunes in the album.
Unexpectedly, the result was different from the previous test. Arabesque was the worst. Again, I felt difficulty of acoustic judgement.
DAD-M100pro > MA-208 > Arabesque
Arabesque sounded cheaply. The sound of piano lacks reverberation. The fruit sounded like a different instrument.
I was using a cheap line cable (Ohm Electric, AUD-C3079S, 3m stereo RCA cable) between the preamp and Arabesque. It bought it for 399 JPY at the nearby DIY store intending to use it to connect a STB (set top box of the cable TV) with the preamp. I used it since it was handy.
I wondered what if I would use a quality cable. At once, I built one out of Mogami Wire & Cable, NEGLEX 2549.
This new cable made SQ better significantly. DAD-M100pro still topped Arabesque, though, the difference was so slight.
DAD-M100pro >= MA-215
I finished the listening tests I had been carrying out for one month. I
installed Arabesque in Gaudi system eventually.
As I described, I had found some minor challenges, but I did nothing about them. The Zobel network was not added yet either. I didn't stick to SQ in full-range use. I wanted to judge SQ in midrange use before solving the problems.
I replaced the midrange cable of the network CD-211B, which was Belden 8412, with NEGLEX 2549.
SQ in midrange use was as good as I had expected. Arabesque excelled DAD-M100pro by far.
MA-215 >> DAD-M100pro
For detailed description about SQ, see "My Own Review."
To the Contents
My first impression was the very low level of noise. Noise wasn't heard
from the highly efficient horn speakers even in a deep, silent night. However,
when I put my ear very close to the left speaker, I heard a subtle hum
noise just like I had heard with FE106 Sigma. I couldn't sense it from
distance of 30cm or more.
Gaudi sound was originally hi-res. I felt Arabesque improved it to higher resolution sound. The sound image was sharper and the localization was more accurate. The new Gaudi sound had higher quality level with higher transparency.
Various musical instruments sounded real. Particularly, the bass, the bass drum and the cello sounded true to life as if I could see real performance.
It's not unusual that bass sounds are improved by upgrading the midrange and/or tweeter. It's no exaggeration that the quality of the midrange unit is more important than that of the woofer to reproduce the sound of the wood bass in Jazz accurately.
I was satisfied with Arabesque. I think I has proved my theory that the high DF amplifier with less current disturbance improves SQ in mid to high ranges.
At first, I didn't feel the sound of piano was not realistic enough. It was resulted from wrong adjustment of the input attenuator. The level was too low. After it was adjusted properly, the sound of piano was improved. Female vocals were improved too.
When DAD-M100pro was used for midrange, a little deviance from the optimal adjustment ruined SQ. With Arabesque, even 10dB of deviance doesn't make me feel odd. It's strange. It's rather difficult to adjust the level when Arabesque is used.
If the level is lower than the optimal level, Gaudi sounds soft and smooth. It might be OK, but the sounds of instruments that have power at high frequencies like the piano become less realistic.
It is natural that Arabesque is usable for me, since it is custom-made.
Before I designed it, I decided where it would be placed. As shown in the above photo, it fits in the bottom part of the TV rack.
Easy access to the rear panel is another advantage. You can access the rear panel only by drawing Arabesque halfway to you (see the left photo). It doesn't fall off the rack since the dirty compartment (the rear half) was heavier than the clean compartment.
It was a good idea too that the stand-off terminals were situated near the output terminals. Thin wires like the 0.4mm single wire can be secured firmly by fixing the sheath with the terminal (the binding post) and soldering the stripped wire to the stand-off terminals (see the middle photo). No worry about breaking the wire.
Arabesque is easy to carry, though I seldom carry it somewhere, because the side channels of the dirty compartment can be handgrips (see the right photo) and the weight is light for a power amplifier (4.4kg).
|Connecting cables||Soldering the cable||Carrying Arabesque|
I like the short readiness time of Arabesque. It needs only one second
from power-on to stable operation. SQ scarcely changes by warm-up. It is
important for me, because I hate waiting.
The Mute Switch is convenient when you want to turn off the midrange only. You can mute the sound without switching off the amplifier. The sound quickly fades out when the Mute Switch is tuned on. I think I should have separated the switch for L/R channels so that each channel can be muted separately.
I already mentioned some challenges. I'll wrap them up here.
The most serious challenge is improvement of stability.
Arabesque has a peak around 250kHz and stability is not perfect. I didn't take the fact seriously that the open-loop gain of LM3886 extends to 200k to 300kHz and it's likely to be unstable at very high frequencies.
I think the closed-loop gain should be higher than the current one (22dB). The power op amp is most stable at some closed-loop gain. The datasheet of LM3886 says that the gain must be 20dB or higher for stable operation and the typical gain is 26 to 46dB. The gain of Arabesque is out of the range.
The sample circuit whose gain is 22dB is introduced in the datasheet and I copied it to avoid complex calculation. I regret I took that easy way. Next time I use LM3886, I'll set the gain at 30dB or higher.
Another solution is to add Zobel network (RSN, CSN) I omitted due to shortage of room. Stability should be improved by making a poler with the network at 100kHz or lower.
It needs know-how to improve stability of an amplifier whose open-loop frequency range is so wide. On the other hand, the same amount of NFB is applied at very high frequencies as in the audible band, and that leads to low distortion and high DF in treble region.
I experienced for the first time that SQ changed a lot by replacing the line cable. I haven't experienced that with the other audio devices I have. I guess this is caused by feed-through distortion of Arabesque.
I guess an input buffer stage could solve this problem. An op amp with low output impedance situated at the front end may prevent ringing from being fed to the input.
I figured out that the input DC blocking network (C1, R1) is not necessary.
The following is a schematic that includes the solutions described above.
I haven't implemented this circuit yet as of July 2016. I haven't simulated it either. I haven't confirmed that it can solve the problems for real. I'll conduct a further examination of the circuit design and apply it to the next "1W amp" (I'm planning MA-217).
There's one more thing; I think I should replace the reservoir capacitors (C106-107, C109-110).
I selected the component without enough consideration, although it is the most important part in the amplifier. It is often true that the quality of the power supply circuit is more influential to SQ than that of amplifier circuit. So full consideration to every parameter, especially ESR and maximum ripple current, is required before the selection.
I regret that I didn't choose FG (Fine Gold) capacitor of Nichicon, the same manufacturer of FW series I selected. The advantage of FG series is its anti-vibration feature. Even though the electrical characteristics of some component is superb, it could impair SQ if it is microphonic. This is one of the reasons why I quit using vacuum tubes.
The rated voltage should be 50V, though I chose 35V. I chose it because I misunderstood that the regulation of the mains transformer was 5%. The actual value is 10%. So the DC supply voltage (VCC/VEE) reaches 30V when the AC supply voltage is the highest in the specification, =110V (+10%). At least 20% of the voltage margin is desirable (the maximum voltage is 28V for the 35V capacitor), so 50V capacitor should be used.
Here are short reviews on new components I used for the first time.
The R-core transformer (Phoenix RA80-260) is a compact transformer with low leakage flux. It is inexpensive for a custom-made transformer. I think it is a good choice.
The breaker-switch (Nikko Electric IBP-1-2A) has a disadvantage. It is its high internal impedance (0.26 ohms @50Hz). I chose the breaker-switch since it is said that fuses will impair SQ. But the high impedance may impair SQ more than fuses.
As Arabesque is "1W amp," the 2A type is too large, but the 1A type has as high as 1 ohm internal impedance. I didn't choose that. Unlike fuses, the breaker-switch is not replaceable. It is inconvenient.
For the next work, I am planning to use an axial lead fuse (soldering type), because I think the problematic component is not a fuse but a fuse holder.
I liked the gold-plated OFC wire (Amtrans GW-T-0.7Of). It is really easy to use.
I made the inductor (L1) for the first time. I used polyurethane wire as many DIY constructors do. I realized later that I should have used the gold-plated OFC wire. I used OFC wires for wiring, but only this polyurethane wire is made of 4N copper. The inductor carries the output current. It is the important part that requires high quality material the most.
The left photo shows the inductor made of the polyurethane wire and used for Arabesque, and the right photos shows a one made of the gold-plated OFC wire. I made it for a trial. I'm planning to use it for MA-217. I think it is better that the one end is soldered to the pin of the IC (LM3886) and the other end is extended to the LS unit. In this way, the number of soldering joints can be reduced and the output terminals can be omitted.
I don't know how much better OFC is than ordinary 4N. But nowadays OFC wires are inexpensive. I'll continue to use OFC for internal wiring.
The P2P board is easy to make and assemble, and has few disadvantages. I'm planning to use it for my future works. However, for high sensitivity amplifiers like a phono equalizer, PCB may be the better choice.
I think it is a good idea to transfer a drawing made with PCB CAD on the board surface. It helped me a lot when I drilled and assembled the boards. However, a further consideration is necessary to know whether or not the transfer paper affects the electrical characteristics (e.g. insulation performance) of the board.
I built the two Amp Boards that are identical, and I installed the one for the left channel upside down in order to keep wires short as possible. The component side is not accessible unless the board is removed off the enclosure. Now I think two different boards should be designed for each channel.
It is so hard to remove the board off the enclosure, because the internal wires are directly soldered to the components on the board. I think some components should have been replaceable while the board is fixed in the enclosure for maintenance.
For high maintainability, using connectors as in commercial amplifiers is one of options. But I hesitate to take this solution, because I believe (or misunderstand) a contact may impair SQ.
The small heatsink caused no problem, even when Arabesque was used as a full-range amplifier. In Gaudi system, dissipation in Arabesque is as small as that in idling state. So enough margin is secured.
I mounted the LEDs for the power indicator on tag strips, and mounted the tag strips with the transparent screws. I think it was waste of time and labor. The simpler way is mounting the LEDs on the Amp Board. The LEDs are bright enough to locate them not so close to the transparent screws.
The red LEDs are used for VCC and the blue for VEE, but this combination of the primary colors is too loud. Filter is desirable to reduce chroma.
When I showed Arabesque to my friend, he pointed out at once that too many screws were used. That was what I was concerned about too. I didn't feel I used
too many screws when I was designing the enclosure, but I felt a bit odd
at the first glance at the real Arabesque.
I aimed at deadening, high thermal conductivity and better shielding with the many screws. But I'll use fewer screws for my next work, because I want to reduce labor for assembly and maintenance.
I think it was right using various types of screws. There was a catch, though. I bought long screws and cut them to the proper length before use. I learned that screws made of stainless steel or brass are hard to cut. I should have bought screws of the proper lengths in the first place.
The vertical clean compartment works as I expected. The smooth air flow helps heat release. The inside temperature is kept low with the few vent holes. The matt black paint on the inside walls helps heat release too. I'm planning to design a similar enclosure for the next "1W Amp" (MA-217).
I used water based paint on the aluminum panels. It was no good. It is so fragile that it can be easily removed. The right photo shows a scratch. When I tried to tighten the screw, I scratched the panel accidentally with the tip of a screwdriver. The paint was removed as indicated by the arrow in the photo.
I successfully painted the face panel of PA-203 many years ago. At that time, I used a spray paint for automobile. Its color was beautiful and it is so durable too. I recommend paint for automobile.
However, I plan not to paint myself in the future. Instead, I'll use finished panels.
As I already described in "Building", the transfer paper (A-one 51112) I used on the face panels is not easy to use. And it is so sticky and hard to remove once it affixed.
I'll try a sticker for the next work. It may look a little cheap, but may be less likely to fail like making letters blurred.
The side panels (P3-P4) are reinforced with the copper panels. The copper panel is dampening vibrations for sure. It is the most effective method to dampen vibrations to combine different materials which have different characteristics.
Though there are some minor challenges, Arabesque lives up to my expectation. I also expect that the system's total sound quality (SQ) can be improved further by building one more chip amplifier similar to Arabesque for the tweeters.
However, I should consider the mechanism that deteriorated SQ when Arabesque was used as the full-range amp. I want to know the cause and the remedy before designing the tweeter amp.
I built Arabesque as a prototype. So I didn't examine the design in detail. But, I'd like to say that you can build a high quality amplifier even though the design is not so perfect. I'd like beginners to know this fact. I recommend you build an amplifier anyhow even if you are not confident to build an amplifier like a professional does.
I wrote this page more detailed than other pages so that a novice can build his Arabesque. I believe any audiophile with basic knowledge about electronics can build a chip amplifier like Arabesque. If this page would be a good reference for you, I'd be happy.
Return to the top of this page